CDS-John Blue

Squeeze Tube Pump Calculator

Calculate the Flow Rates for Your CDS-John Blue Pumps

If this is your first time using the calculator, please review the instructions below

Squeeze Tube Pump Flow Rate Pump Calculator
Squeeze Tube Pump Model

English or Metric Units


Drive System

and my loaded radius is: (distance from tire or axle center to the ground when in use)
Inches

OR

and my loaded radius is: (distance from axle or press wheel center to where it touches the larger tire)
Inches (optional)
Row Space

Inches
Number of Teeth: Drive Sprockets
(To decrease pump setting, increase drive number of teeth. To increase pump setting, decrease drive number of teeth)

(required)
(optional)
(optional)
(optional)
Number of Teeth: Driven Sprockets
(To decrease pump setting, decrease driven number of teeth. To increase pump setting, increase driven number of teeth)

(required)
(optional)
(optional)
(optional)
Ground Speed

Miles Per Hour
Terms of Use:
I understand that CDS-John Blue Company is furnishing this calculator "as is" and that it is not covered by any warranty whatsoever, whether express, implied, or statutory, including, but not limited to, its freedom from errors, its fitness for any particular purpose, and/or its correct or incorrect use. I agree that by using this calculator, I am doing so at my own risk. I agree to hold CDS-John Blue harmless for any and all damages directly or indirectly related to the use of this calculator. In no respect shall CDS-John Blue Company incur any liability for any damages, including, but not limited to, direct, indirect, special, or consequential damages arising out of, resulting from, or in any way connected to the use of this calculator, whether or not based upon warranty, contract, tort, or otherwise; whether or not injury was sustained by persons or property or otherwise; and whether or not loss was sustained from, or arose out of, the results of this calculator and its use.

WARNING:
I understand that all calculations are based upon the information I provide. Always verify the calculated information before entering the field as variables within your system can cause differences between calculated rates and actual output rates.



Click the button below to access your pump settings.
then scroll down this page to see your pump settings.
Pump Setting & Application Parameters (Estimated)
Pump Selected:
Fixed Output: Gallons Per Acre
Sprocket Ratio:
Pump RPM: RPM  

Supported Devices:

  • This calculator is an advanced web application that requires certain functionality of your smartphone or tablet device. Not all devices will work. However, late-model smartphones and tablet devices (such as Apple iPhones/iPads, most Android devices, Windows Phones, and Blackberries) that offer full support for HTML, JavaScript, and Dynamic HTML standards will work appropriately. Contact your device manufacturer for questions about compliance to these standards.

Online Instructions:

  • Complete all form fields (except those marked as optional) within the blue section.
    1. From the pull-down menu near the top, select your CDS-John Blue "Squeeze Tube Pump Model".
    2. Select whether you work in "English Units" or Metric Units" of measurement.
    3. Click the bubble next to your type of "Drive System" and enter your "Loaded Radius" in the field immediately below it.
    4. Enter your "Row Space".
    5. Enter the number of teeth for your "Drive Sprockets" (use multiple rows if necessary).
    6. Enter the number of teeth for your "Driven Sprockets" (use multiple rows if necessary). For each "Drive Sprocket" field you completed, make sure you complete the corresponding "Driven Sprocket" field.
    7. Enter your "Ground Speed".

  • Double-check all the fields you just entered for correctness.

  • Read the "Warning" within the pink section titled "Terms of Use".

  • Acknowledge that you have read the "Warning" and indicate your acceptance of the "Terms of Use" by putting a check in the checkbox next to "I understand...".

  • Click the button that says, "Calculate My Pump Settings".

  • Scroll down to the green section of the page titled "Pump Setting & Application Parameters (Estimated)" to view your CDS-John Blue pump settings.

  • NOTICE: If after viewing your calculated pump settings, you decide to change any of the input form fields, be sure to resubmit your changes by clicking the gray "Calculate My Pump Settings" button once again. Failing to do so will result in improper pump settings.

Offline Instructions:
(for use when an Internet connection is not available)

  • While it is best to have a live Internet connection, it is possible to use the calculator offline on many mobile devices. Try the following:
    • View the calculator somewhere where Internet connectivity is available. Once the calculator is available on your mobile device, leave your browser running and enter the field where Internet connectivity is not available. The calculator should will still work.

  • If that doesn't work, try the following:
    • Try downloading an app for your mobile device that allows you to view web pages offline. Be sure the app works in conjuction with your web browser or supports JavaScript. JavaScript is the programming that performs the mathematics necessary to calculate your pump settings.

  • Your final option:
    • If neither of the above options work for you, your only alternative is to gather the information required by the calculator and enter the information when you have a live Internet connection.

  • Once you can view the calculator, complete all form fields (except those marked as optional) within the blue section.
    1. From the pull-down menu near the top, select your CDS-John Blue "Squeeze Tube Pump Model".
    2. Select whether you work in "English Units" or Metric Units" of measurement.
    3. Click the bubble next to your type of "Drive System" and enter your "Loaded Radius" in the field immediately below it.
    4. Enter your "Row Space".
    5. Enter the number of teeth for your "Drive Sprockets" (use multiple rows if necessary).
    6. Enter the number of teeth for your "Driven Sprockets" (use multiple rows if necessary). For each "Drive Sprocket" field you completed, make sure you complete the corresponding "Driven Sprocket" field.
    7. Enter your "Ground Speed".

  • Double-check all the fields you just entered for correctness.

  • Read the "Warning" within the pink section titled "Terms of Use".

  • Acknowledge that you have read the "Warning" and indicate your acceptance of the "Terms of Use" by putting a check in the checkbox next to "I understand...".

  • Click the button that says, "Calculate My Pump Settings".

  • Scroll down to the green section of the page titled "Pump Setting & Application Parameters (Estimated)" to view your CDS-John Blue pump settings.

  • NOTICE: If after viewing your calculated pump settings, you decide to change any of the input form fields, be sure to resubmit your changes by clicking the gray "Calculate My Pump Settings" button once again. Failing to do so will result in improper pump settings.

| Home | Contact |

Copyright © 2011, CDS-John Blue Company. All Rights Reserved.